For how to set the date and time, see page Page 5: Deleting Files Sanyo declines any claim for compensation for recorded contents etc. When you are finished deleting files, press the MENU button. Turn on the computer, and use the supplied dedicated USB interface cable to connect your camera to the computer. Failure to follow this procedure may cause faulty operation of your computer or corrupt the files in your camera.
Left-click on the icon for safely removing hardware in the task tray. English i Lithium-ion battery pack charger and power cord: 1 i Dedicated AV interface cable page 39 : Connect the supplied power cord to the socket on the battery pack charger.
Insert the battery pack in the battery charger. Page Charging The Battery Pack Charging the battery pack Be sure to fully charge the supplied or separately sold battery pack before using it in your camera.
For charging the battery pack, use the supplied charger. Charge the battery pack if it is being used for the first time, and recharge it whenever the remaining charge is low. Please refer to the following table if the indicator flashes abnormally. If an unformatted card is used, the card itself may become unusable. Card slot cover 4 Close 1 Raise up 2 Swivel If the multi-indicator is flashing red However, a battery that is difficult to insert because it has become swollen may then be impossible to extract from the battery compartment.
Page Turning On The Camera When The Power Save Sleep Mode Is Active Turning on the camera when the power save sleep mode is active In order to preserve battery pack power, the power save sleep function will automatically turn off the camera after about 1 minute of no use during shooting, or about 5 minutes of no use during playback factory-preset setting.
About the standby mode i To turn off the camera only briefly, you can close the monitor unit to put the camera in the standby mode. Therefore, before capturing images, make sure the correct date and time are set.
Page 30 Set the clock. HINT i Under normal conditions, while the battery pack is being replaced, an internal battery will maintain the date and time settings. However, there is a small chance the settings may be lost the backup will last for about 7 days. Turn on the camera page Select the mode that is suitable for your purposes. Select the desired operating mode page Toggle the SET button to the right. HINT About the applicable mode indicator i This indicator shows the shooting mode s for which the selected setting is Press the [ ] button.
Turn on the camera page 17 , and set it to the recording mode page What is the camera focusing on? Point the camera lens at the subject. Select the image to play back. Page 45 Video clip playback operation To do this Normal forward playback Stop playback Pause To play back During forward one image playback at a time During reverse single- playback frame step During forward playback Slow playback During reverse playback Forward playback accelerate playback Reverse Select the desired aspect ratio, and press the [ that if the video clip aspect ratio is , you cannot select Use the TV controls to adjust the volume.
If Adobe Reader is not already installed on your computer, a link to the website from which you can download it can be found on our website. This program cannot be accessed while a card is installed in the camera.
Start your computer, and use the supplied dedicated USB interface cable to connect your camera to the computer. If Adobe Reader is not already installed on your computer, a link to the website from which you can download it can be found on the Sanyo website. Why is the battery pack consumed so quickly even after it was fully recharged? Outline of Operation Page 5 4.
Lens drive block 5. Video Clip Recording and Playback Focus drive Page 6 7. Power Sequencer Description For the overall configuration of the power sequenser, refer to the block diagram. This circuit block consists primarily of the power sequencer block inside the ASIC. Page 7 8. Key Operaiton For details of the key operation, refer to the instruction manual. Key Operation 9.
Receiving user operations showing that the camera has been turned on When the battery is installed, the 3. Page 8 Outline 3. Digital 3. Page 9 Charging Circuit 2. Page Disassembly 2.
Spacer joint base 9. Screw 1. Spacer batt box Assy, cabi left 3. Two screws 1. Cover DC 4. Cabinet top Cover battery 5. Page 11 Heat sink tape left Shield tape ST1 2. Spacer ST1 cover 3. Cover condenser Heat sink left Page 12 Spacer CA1 CN Connector CN 2. Heat sink tape top Unit control 3. Connector CN CP1 board 4. Spacer battery 5. Holder lens Heat sink rub heat L 6. Page 13 Shield tape bottom 2. Cover joint base Spacer CP1 2 3. Spacer speaker wire Spacer button power 4. Speaker, 8 Heat sink right 5.
Page 14 Spacer joint removed after assembly LCD 2. Assy, joint Spacer VF 3.
0コメント